Q: How do I purchase Moog Sensor and Surveillance Systems’ products?
A: Moog products are available directly and also through a global network of distributors. Visit the “Contact Us” section of www.moogs3.com for a list of Business Development Managers
Q: Does Moog offer “Project Pricing”?
A: Yes! Contact your area Business Development Manager for details.
Q: Does Moog offer OEM/ODM services?
A: Yes! Contact Andrew Zeilenga at +1 847.715.7548 for details.
Q: Have Moog Videolarm and Moog Quickset merged into one company?
A: Yes, we are now Moog Sensor and Surveillance Systems with offices in Northbrook, IL and Decatur, GA. Through this consolidation, we are maintaining our high standard of innovative product offerings and superior customer service.
Cameras and Enclosures
Q: How do I set up my camera surveillance system on a wireless network?A: Contact Moog Technical Support at +1 847.498.0700 or +1 847.715.7538
Q: For outdoor Camera Enclosures, which wires power the camera and which power the heater/blower?
A: The cables are color coded for your convenience:
red/orange = camera power
yellow/green = heater/blower
Q: What if I suspect missing parts in my product box?
A: Product instruction sheets list all products that should be contained within each box. If you are missing a part or have received the wrong part, contact customer service at 800.247.6563 for assistance.
Q: Which camera mounting options does Moog offer?
A: Moog offers the following mounting options:
- Parapet (PRM50G, PRM30G, WM30G)
- Gooseneck (WM20G, WM10G)
- Corner (ACA2, CA2)
- Wall (WM1500, WM800, APM6B, APM6W and WM40W)
- Pole (APM3, PM3, WM2400, APM6B and APM6W)
- Pendent (PRM50G, WM20G, CA15, WM10G)
- Ceiling (CA15, CM900)
- Stainless Steel (WM10SS, WM1000SS)
---Visit the product section of www.MoogS3.com to see a full selection of mounts and brackets.
Q: Which power supply does my camera housing need?
A: -40va for box camera housings
- 80va for all domes with 1 heater/blower
- 100va for all housings with 2 heaters/blowers
Q: Where can I find product installation instructions or product specifications for Moog Sensor and Surveillance Systems’ products?
A: Installation instructions and specifications for many cameras and enclosures are located at www.moogS3.com - search by product. Or, call customer service at 800.247.6563 for assistance.
Q: I’ve followed the product instructions and my camera is not operational. How can I get additional assistance?
A: Moog technical support is available at +1 847.498.0700, please call for assistance.
Q: Can I register my products to ensure product updates reach me
A: Yes you can. Visit the Product Registration section and complete the registration form.
Q: I'm using Pelco D for control of my GeminEye system and the thermal camera
A: Upon application of power to the GeminEye, the cameras are supposed to generate a video image. A few customers have stated that their cameras default have been set to "off". Typically this is easily corrected using the Test Emulator and resetting the default, however when a customer is using Pelco commands, this feature is not available directly.
There is a way to set (and reset) the default power setting using Pelco D commands.
Pelco Preset command 83 turns the camera ON.
Pelco Preset command 84 turns the camera OFF.
Pelco Preset command 41 stores the current camera state as the initial state.
For example, if we ship a product with the unit set to "CameraON", and the customer sends the command "Preset 84", the camera will shut off. If they then send "Preset 41", the current camera state (OFF) will be stored as the initial state at power up of the GeminEye.
Pan and Tilt Positioners
Q: I've installed my pan/tilt into my security/surveillance system and it's not moving when commanded and not transmitting any video image.
A: All of our pan/tilts are delivered with a 6' test cable and remote emulator software that allow you to troubleshoot the pan/tilt independently from your control system. If the pan/tilt is tested using the supplied test cable and remote emulator software and functions normally, the problem lies within the control system, not the pan/tilt.
- Verify that the unit is receiving the proper operating voltage. Check the schematic/wiring diagram that was delivered with your pan/tilt to make certain the proper supply voltage is being applied to the correct pins on the base connector.
- Make sure the communication setting for the pan/tilt matches the communication method you are attempting to use. Moog pan/tilts can be setup to communicate in RS-232, RS-422 and IP protocols. Make sure the baud rate and communication (com) port settings for the control system and the pan/tilt are the same. If you have changed com port settings make sure you have power cycled the pan/tilt so it can sync with the new settings.
For other Pan and Tilt Positioner, or Tripod related questions, please contact us at: +1 847.498.0700.
Have a Question?
For inquiries on all Moog S3 products,
call +1 847.498.0700
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
3650 Woodhead Drive
Northbrook, IL 60062, USA